Outhaul Jammer

I'm working thru my backlog - this is an old post from Drew at Sail Delmarva - so old in fact that he has sold this boat and gotten a new one since this was posted. And the book he mentions has already been published - I recommend it and several others he has published. You can find them in his bookstore.

As I continue to work on my book on "Faster Cruising" I found myself feeling like the cobbler with no shoes for his children; I don't always follow my own advise, even when I know I'm right. In the book I argue that cruising boats are often lack the rigging and hardware needed to make basic trim adjustments quickly and easily, as though cruisers don't care about efficient sailing or understand the fine points. I care, but I have to admit my cruising cat doesn't have the quick access to fine trim that my performance cat had. I aim to fix that.

Case in point. My PDQ 32 came with a good boom and internal reefing, but the main outhaul was secured to an undersized cleat . To tension it under load, you take the tail to a mast-mounted winch, wrap the line under the cleat, and lift the line sharply when taking the line off the winch in an attempt to minimize slippage before that first wrap is on the cleat. Boy scout at best.

A few days ago I removed the undersized cleat (closely spaced holes on the seam) and I tapped four new holes to secure a proper jammer. Now I can ease the outhaul in a blink and tighten with a winch in control.

The smaller line is for the lazy jacks.

Why a double jammer? The few times I have found myself sailing with three reefs (winds gusting to over 30 knots) I found I needed a better way to winch the clew down. The tack is easily secured with a loop through the reefing tack and under the gooseneck, but there is no internal rigging for a 3rd reef. Thus, I tie a bowline around the boom under the reef clew (like the other reefs), go up through the reefing clew, and back to a snap shackle-equipped snatch block at the main outhaul. From there the reefing line is threaded through this new jammer, allowing a mast mounted winch to tension the clew outhaul.

The only challenge is to remember to thread the reefing clew while hoisting.

[The jammer came courtesy of freecycle--it patiently awaited re-purposing for several years in one of my might-need bins. Whooppee!]

Aft Cabin Project

Please welcome new contributors Deb and Tim, who live aboard and cruise their Tartan 42, s/v Kintala. If you live aboard your boat, you undoubtedly work on your boat. So where do the tools, electrical connectors, plumbing bits, spare pieces of precious teak, etc go? Deb and Tim created a nicely organized storage area for just these things...

The aft cabin is finished with the exception of a few coats of wax so here are the pics for your perusal.

This is the starboard aft cabin berth that we removed the mattress from. We bought these hardwood drawers from Lowes in a kit for less money than we could have bought the materials.

Tim built a bulkhead across the foot of the berth at the same location as the front of the pantry cupboard. The area behind this bulkhead will store boxed tools like drills and the Dremel. In this picture he's working on installing the wire shelves that will hold our Harbor Freight plastic storage boxes. And yes, we know the shelves are upside down. We needed the lip to keep the boxes from sliding back and forth every time we tack.

The finished project minus the waxed finish. There is a handy shelf on the top for putting the tools currently being used. Below the hinge are the two drawers that hold tools. You can now see the door on the bulkhead to access the boxed tool storage. We left enough room then in front of the drawers for guests to put their duffels.

Here it is with the front panel lowered on the hinge. This makes our workbench which will soon have a quick-mount vice on the corner in the front of the picture. It's hard to see in the picture, but under the workbench are three drawers that we put 100# heavy duty sliders on and locks to hold our heaviest tools.

The drawers have good sliders on them and are stopped by the fiddle.

The cupboard at the foot holds an amazing amount of junk tools.