“I’m so happy to have found a leak on my boat!” she says with a big smile. The expressions on others’ faces are astounded, confused, or horrified.
“OK, how about I finally LOCATED a leak on my boat!” The response is definitely more congratulatory, occasionally tinged with a little sadness or jealousy. Rubigale’s starboard side has been plagued with leaks since I bought her in the summer of 2014.
Once the torrential downpours of the Seattle fall appeared, drips ran down the overhang in the salon and puddled on the shelf. One of the three screws that holds in my barometer would cry every time it rained. I started finding things in the starboard aft berth wet, requiring everything to live in a plastic bin.
I thought I had it solved when I replaced one of the larger windows in the salon after I spotted dampness at the corner, and although the leaking seemed to have lessened, it was definitely still there. I tried caulking the toe rail and honestly most anything that looked caulk-able. I had the rigging tuned, and the shroud plates were rebedded in the process.
Still, the insides of cabinets mildewed and were regularly vinegared and bleached. Every time it rained, a pile of boat rags came out to soak the puddles, and on a particularly hard pour, a few pots came out as well. The bilge pump would come on. The dehumidifier got a workout. The headliner remained mysteriously dry.
There was old water staining around the aft-most starboard port light, but all six of them were brand new when I purchased the boat and I assumed that the new ones were the fix for that problem. I began to blame the jib track and the bow hardware, and started to wrap my mind around how to do all of these things, or what it would cost to hire someone to do it.
Everyone knows it rains a lot in Seattle, but it is typically a persistent mist rather than the torrential downpours I remember in Mississippi. Recently, Seattle experienced one of those deluges and I caught the leak from the port light red-handed! I had already rebedded one window, and this was so much smaller and seemed easier. You can probably see where this is going.
Preparing to Wrestle
This Came off Much Too Easily
Since it was a different type of window, I watched a YouTube video on the process and felt I was ready to go. I unscrewed the inner portion of the port light with it’s spigot and removed it easily. I had expected it to be much more difficult because some veneer is torn away from a couple of the ones in the V-berth, suggesting it was going to be a bear. With the larger window, there had been screws attaching the inside frame to the outside frame to create compression for the sealant. None of that was here. The inside was screwed to the wood and the spigot extended to the outside of the fiberglass where a trim piece was simply adhered with some sort of sealant which was pressed into the gap. The trim piece was also easily (too easily) removed and staining on the underside and on the fiberglass showed where the leak was happening.
Staining Where Water Intrusion Was Occurring
Area Where the Leak Was Damaging the Wood
I’m fortunate to have solid fiberglass, so there was no soggy core. There is a small gap between the fiberglass and the wood walls which was where most of the water had been going. The side of the wood facing the fiberglass was soggy and spongy in the area of the leak. The uncharacteristic 90 degree weather helped it dry out over a day with the assistance of a fan. Meanwhile, I started looking for answers. Why didn’t the screws connect the inside to the outside? How could you achieve a seal without the compression?
It was time to phone a friend. John, who had helped me replace the larger window, came over and looked at it, and agreed that it just didn’t seem correct. We made a field trip to the marine store and described the problem and brought the port light. After tossing around some ideas, a solution was proffered to cut a larger hole in the wood so that the inside section of the window would be directly against the fiberglass! To say I was skeptical, and a little bit horrified was an understatement. I said I’d think about it and picked up the type of sealant that was recommended for plastic.
Through-bolting the Port Light
It was time for a glass of wine and more research. It’s amazing what you can discover when you read the instructions. There were very clear directions (with pictures) on how to through bolt the window for a solid wall as well as a multi-layered wall like mine. There is 1/4” of fiberglass, 1/4” of space, then 1/4” of veneered plywood on the inside.
The solution was to fill the gap as much as possible with closed cell spray foam to provide some structure for the gap under compression. I dreaded this part because I have had a few experiences with this stuff in old houses that were pretty messy. I made a part list of screws, barrel nuts, mineral spirits and the foam and went shopping.
Closed Cell Foam
Closed Cell Foam in the Gap
The following day the wood seemed dry and I filled the gap with the spray foam. Every time I revisited the opening, more foam had expanded out and had to be cut away, but by the next morning it seemed pretty solid and ready to go. The wood felt dry. Now it was time to drill holes in my boat which scares the living daylights out of me, so I again phoned a friend.
Trim Piece as Template
That Side Hole was a PAIN
Following the recommendations on the company website, we drilled holes through the trim piece and the fiberglass to match those in the wood where the spigot was attached. Due to the placement of one of the shrouds, lining up one of the holes was next to impossible which was remedied by making a slightly bigger hole (giving me slightly more anxiety). The edges of the holes and the main opening were chamfered so they could accommodate more sealant. The product recommended to stick to both plastic and fiberglass was Sudbury Elastomeric Marine Sealant.
table align="center" cellpadding="0" cellspacing="0" class="tr-caption-container" style="margin-left: auto; margin-right: auto; text-align: center;">
Once the fiberglass dust was cleaned up and a dry fit done, it was a fairly simple job with two people to get it sealed and the bolts threaded into the barrel head nuts on the inside. I used plenty of sealant, resigning myself to a big clean up, but erring on the side of too much.
I’m very happy to report that after a couple of pretty hard rains, the window, the barometer and the shelf remain dry! There’s still the leak somewhere behind the oven, and I still have 5 more port lights to rebed, but for now, Rubi is drier than she has been in the last two years.
Update August 30, 2016- I am deliriously happy to say that after two crossings of the Strait of Georgia, the starboard side is DRY!
Monday, January 9, 2017
'Tis the season. At least here in the PNW: rain, rain, and more rain. And over on s/v Rubigale, Dana has found a solution to a problem we have all had at one time or another... a leaking port: